This video shows you how to configure OSPF (Open Shortest Path First) routing protocol on the GNS3 network simulator program. ✅ S U B S C R I B E ► goo.gl/8d0iG9 ✅ Article ► www.sysnettechsolutions.com/en/configure-ospf-on-cisco-router-in-gns3/ To configure the #OSPF Routing: Step 1: If you have not installed #GNS3 before, please refer to videos of GNS3 installation on Windows, Linux, and macOS. Windows ➦ www.youtube.com/watch?v=yuJ5qXFpr7Q Linux/Ubuntu ➦ www.youtube.com/watch?v=b6A2peSovLU macOS ➦ www.youtube.com/watch?v=MWStTRpwqBY Step 2: After you have done the GNS3 setup, open it and drag and drop 2 Cisco Routers into the workspace. Step 3: Add Serial Interface to Cisco Routers. Step 4: Add two Cisco Switches to the GNS3 workspace. Step 5: It is more advantageous to use Cloud PC on GNS3 and you can also work better on Cisco exams with VMware Workstation integration with GNS3. Step 6: To configure your Cloud PC, please refer to the following video or article. Video ➦ www.youtube.com/watch?v=DVokiwWzlxk Article ➦ www.sysnettechsolutions.com/en/configure-cloud-in-gns3/ Step 7: Before configuring OSPF, specify the IP blocks for the two different networks. For example; Network A ➦ 192.168.5.0/24 Network B ➦ 192.168.10.0/24 Step 8: Run the network devices. Step 9: Do the IP configuration of Cloud PCs by opening virtual machines on VMware Workstation. Step 10: Check your VMware Virtual Network Editor settings for the Cloud PC. Configure VMnet information correctly. Step 11: Open the CLI command prompt for Routers and follow the commands below to enable OSPF. R1# conf t R1(config)# router ospf 10 R1(config-router)# network 10.1.1.0 0.0.0.3 area 0 R1(config-router)# network 192.168.5.0 0.0.0.255 area 0 R1(config-router)# end R2# conf t R2(config)# router ospf 10 R2(config-router)# network 10.1.1.0 0.0.0.3 area 0 R2(config-router)# network 192.168.10.0 0.0.0.255 area 0 R2(config-router)# end Step 12: Watch the video for the remaining steps. Step 13: Don't forget to subscribe to our YouTube channel for more videos on Cisco training with GNS3! ────────────BEST PRODUCT FOR OSPF──────────── ✅ Buy ► bit.ly/AnatomyofOSPF ───────────────RELATED VIDEOS─────────────── ➊ How to Integrate VMware with GNS3 ➦ www.youtube.com/watch?v=SwE9VaZ7lXQ ➋ How to Configure RIP ➦ www.youtube.com/watch?v=839dk8lYhFU ➌ How to Configure Cloud ➦ www.youtube.com/watch?v=DVokiwWzlxk ➍ How to Install GNS3 2.0 ➦ www.youtube.com/watch?v=PpIknkJG2dA ➎ How to Configure DHCP Relay Agent ➦ www.youtube.com/watch?v=TxR1kiQJ4G4 ───────────────FOLLOW US─────────────────── ✔ Facebook ➦ www.facebook.com/SysnettechSolutions/ ✔ Twitter ➦ twitter.com/SysnettechS/ ✔ Pinterest ➦ www.pinterest.com/SysnettechS/ ✔ Instagram ➦ www.instagram.com/sysnettech_solutions/ ✔ LinkedIn ➦ linkedin.com/in/tolqabaqci/ ███████████████████████████████████████████

Be the first to comment