This video shows you the steps to configure EIGRP routing on Cisco Routers using the GNS3 network simulator program. ✅ S U B S C R I B E ► goo.gl/8d0iG9 ✅ Article ► www.sysnettechsolutions.com/en/configure-eigrp-on-cisco-router-in-gns3/ To configure the #EIGRP Routing: Step 1: If you have not installed #GNS3 before, please refer to the following videos to install it on Windows, Linux, and macOS. Windows ➦ www.youtube.com/watch?v=yuJ5qXFpr7Q Linux/Ubuntu ➦ www.youtube.com/watch?v=b6A2peSovLU macOS ➦ www.youtube.com/watch?v=MWStTRpwqBY Step 2: After installing the simulator software on your system, add 2 Cisco Routers, Cisco Switches, and Cloud PCs to the GNS3 workspace for EIGRP configuration. Step 3: If you do not know how to configure Cloud PC on GNS3, please refer to the following video or article. Article ➦ www.sysnettechsolutions.com/en/configure-cloud-in-gns3/ Video ➦ www.youtube.com/watch?v=DVokiwWzlxk Step 4: It is useful to use the Cloud PC. You can use Cloud PCs by integrating VMware with GNS3. Step 5: Add Serial Interface to Cisco Routers. Configure the connection between the Routers using Serial cable, and finally configure the IP configuration of the Serial Interface. Step 6: Assign IP addresses to the FastEthernet interfaces of Routers. Step 7: Connect Switches to Routers and power on all network devices. Step 8: Define IP blocks on the network topology before configuring the routing. Step 9: Apply the following commands to enable EIGRP. R1# conf t R1(config)# router eigrp 1 R1(config-router)# network 10.1.1.0 0.0.0.3 R1(config-router)# network 192.168.5.0 0.0.0.255 R1(config-router)# end R2 # conf t R2(config)# router eigrp 1 R2(config-router)# network 10.1.1.0 0.0.0.3 R2(config-router)# network 192.168.10.0 0.0.0.255 R2(config-router)# end Step 10: Do not forget to subscribe to our YouTube channel for more videos on Cisco networking with GNS3! ───────BEST PRODUCT FOR CISCO TRAINING──────── ✅ Buy ► bit.ly/CiscoCertification ───────────────RELATED VIDEOS─────────────── ➊ How to Integrate VMware with GNS3 ➦ www.youtube.com/watch?v=SwE9VaZ7lXQ ➋ How to Configure RIP ➦ www.youtube.com/watch?v=839dk8lYhFU ➌ How to Use VPCS in GNS3 ➦ www.youtube.com/watch?v=YUN38b9pRn8 ➍ How to Configure RIP Version 2 ➦ www.youtube.com/watch?v=1tsGWuCtEIw ➎ How to Configure OSPF ➦ www.youtube.com/watch?v=gFMvgpDSzlI ───────────────FOLLOW US─────────────────── ✔ Facebook ➦ www.facebook.com/SysnettechSolutions/ ✔ Twitter ➦ twitter.com/SysnettechS/ ✔ Pinterest ➦ www.pinterest.com/SysnettechS/ ✔ Instagram ➦ www.instagram.com/sysnettech_solutions/ ✔ LinkedIn ➦ linkedin.com/in/tolqabaqci/ ███████████████████████████████████████████

Be the first to comment