This video shows you how to configure Static NAT on Cisco Router using the Packet Tracer software. ✅ S U B S C R I B E ► goo.gl/8d0iG9 ✅ Article ► www.sysnettechsolutions.com/en/configure-static-nat-in-cisco-packet-tracer/ To configure #Static #NAT: Step 1: If you have not installed #PacketTracer before, please refer to the following videos to install Packet Tracer on Windows, Linux, and macOS. Windows ➦ www.youtube.com/watch?v=pNLhTixgCXg Linux / Debian ➦ www.youtube.com/watch?v=aMnumAyFxCQ macOS ➦ www.youtube.com/watch?v=cXaqjFukSAI Step 2: After installing it, add two Cisco Routers, one Cisco Switch, and two computers to the Packet Tracer workspace. Step 3: Specify local and WAN IP addresses. Step 4: Configure the 192.168.1.0/24 network for the local network and the 10.0.0.1/30 network for the WAN. Step 5: Assign IP addresses to the computers on the local network. Step 6: Assign IP addresses to the GigabitEthernet interfaces of Router0 and Router1 and turn the ports on. Step 7: Test the connection by pinging Router1 over PC0 and PC1. Step 8: Next, configure the interface as follows because the Gig0/1 interface of Router0 is in the IP NAT INSIDE field. R1# conf t R1(config)# interface gig0/1 R1(config-if)# ip nat inside R1(config-if)# exit R1(config)# interface gig0/0 R1(config-if)# ip nat outside Step 9: After you have defined the Router's IP NAT regions, execute the following command to configure Static NAT in Router0 global configuration mode. R1# conf t R1(config)# ip nat inside source static 192.168.10.10 10.0.0.1 Step 10: If you ping Router1 over PC0, you can see that the network connection is established. Step 11: Now, ping to Router1 from PC1 and check that PC1 cannot reach Router1. Step 12: Since we have not configured Static NAT for PC1, PC1 will not be able to reach Router1. Step 13: Execute the following commands in user mode to verify and control Static NAT. ➦ show ip nat translation ➦ show ip nat statistics ➦ clear ip nat statistics ➦ debug ip nat Step 14: Don't forget to subscribe to our YouTube channel for more videos on Cisco Networking training with Packet Tracer! What is Static NAT? Static NAT creates a fixed translation of real address(es) to mapped address(es). With dynamic NAT and PAT, each host uses a different address or port for each subsequent translation. Because the mapped address is the same for each consecutive connection with static NAT, and a persistent translation rule exists, static NAT allows hosts on the destination network to initiate traffic to a translated host (if an access list exists that allows it). The main difference between dynamic NAT and a range of addresses for static NAT is that static NAT allows a remote host to initiate a connection to a translated host (if an access list exists that allows it), while dynamic NAT does not. You also need an equal number of mapped addresses as real addresses with static NAT. ──────BEST PRODUCT FOR CISCO TRAINING─────── ✅ Buy ► bit.ly/CiscoNetworkingDummies ───────────────RELATED VIDEOS─────────────── ➊ How to Configure RIP Routing ➦ www.youtube.com/watch?v=x3Oz4Y4j9GM ➋ How to Configure Static Routing ➦ www.youtube.com/watch?v=H75sduHNruk ➌ How to Connect Two Networks in Packet Tracer ➦ www.youtube.com/watch?v=ujcIlNG6fdM ➍ How to Configure RIP Version 2 ➦ www.youtube.com/watch?v=RwiKhrLkHgw ➎ How to Configure EIGRP ➦ www.youtube.com/watch?v=vhVmum82qjE ───────────────FOLLOW US─────────────────── ✔ Facebook ➦ www.facebook.com/SysnettechSolutions/ ✔ Twitter ➦ twitter.com/SysnettechS/ ✔ Pinterest ➦ www.pinterest.com/SysnettechS/ ✔ Instagram ➦ www.instagram.com/sysnettech_solutions/ ✔ LinkedIn ➦ linkedin.com/in/tolqabaqci/ ███████████████████████████████████████████

Be the first to comment