How to Configure EIGRP on Cisco Router in Cisco Packet Tracer | SYSNETTECH Solutions | Read More ⬇️ 🔗 Article: www.sysnettechsolutions.com/en/ciscopackettracer/configure-eigrp-in-cisco-packet-tracer/ ✅ S U B S C R I B E ► goo.gl/8d0iG9 This video shows you how to configure the EIGRP (Enhanced Interior Gateway Routing Protocol) protocol on the Packet Tracer, a routing protocol specific to Cisco-only devices. To enable EIGRP on Cisco Router: Step 1: If you have not installed Packet Tracer before, please refer to the following videos to install it on Windows, Linux, and even macOS. Windows ➦ www.youtube.com/watch?v=pNLhTixgCXg Linux/Ubuntu ➦ www.youtube.com/watch?v=rwGuAbiGPdc MacOS ➦ www.youtube.com/watch?v=cXaqjFukSAI Step 2: After installation, add 2 Cisco Routers, Cisco Switch, and PC to the workspace. Step 3: Add Serial Interface to Cisco Routers and connect Serial DCE cable to each other. Step 4: Connect the Cisco Switches to the GigabitEthernet interfaces of the Routers. Step 5: Define IP blocks to configure EIGRP. Step 6: The IP block between Cisco Routers must be different from the local network. Step 7: Connect the PCs to Cisco Switches and configure the IP configurations. Step 8: Open the Serial and GigabitEthernet interfaces of the routers with the shutdown command and assign the IP addresses. Step 9: To configure EIGRP on routers, use the following commands as an example. R1 # conf t R1 (config) # router eigrp 1 R1 (config-router) # network 10.1.1.0 0.0.0.3 R1 (config-router) # network 192.168.5.0 0.0.0.255 R1 (config-router) # end R2 # conf t R2 (config) # router eigrp 1 R2 (config-router) # network 10.1.1.0 0.0.0.3 R2 (config-router) # network 192.168.10.0 0.0.0.255 R2 (config-router) # end Step 10: Don't forget to subscribe to our YouTube channel for more videos on Cisco routing protocols! ➦ goo.gl/8d0iG9 ──────BEST PRODUCT FOR CISCO TRAINING─────── ✅ Buy ► bit.ly/CiscoNetworkingDummies ───────────────RELATED VIDEOS─────────────── ➊ How to Use Packet Tracer ➦ www.youtube.com/watch?v=2VL3rjZ_Wmw ➋ How to Configure RIP Routing ➦ www.youtube.com/watch?v=x3Oz4Y4j9GM ➌ How to Configure RIP Version 2 ➦ www.youtube.com/watch?v=RwiKhrLkHgw ➍ How to Configure OSPF ➦ www.youtube.com/watch?v=xF4xd4cEDXg ➎ How to Configure DHCP Relay Agent ➦ www.youtube.com/watch?v=kIBviWl-378 ───────────────FOLLOW US─────────────────── ✔ Facebook ➦ www.facebook.com/SysnettechSolutions/ ✔ Twitter ➦ twitter.com/SysnettechS/ ✔ Pinterest ➦ www.pinterest.com/SysnettechS/ ✔ Instagram ➦ www.instagram.com/sysnettech_solutions/ ✔ LinkedIn ➦ linkedin.com/in/tolqabaqci/ ███████████████████████████████████████████

Be the first to comment